Our Services

Get 15% Discount on your First Order

Lab – Building a Switch and Router Network Lab – Building a Switch and Router Network Topology

April 11, 2024

Lab – Building a Switch and Router Network

Device	Interface	IP Address	Subnet Mask	Default Gateway
R1	G0/0	192.168.0.1	255.255.255.0	N/A
	G0/1	192.168.1.1	255.255.255.0	N/A
PC-A	NIC	192.168.1.3	255.255.255.0	192.168.1.1
PC-B	NIC	192.168.0.3	255.255.255.0	192.168.0.1

Objectives

Part 1: Set Up the Topology and Initialize Devices

Part 2: Configure Devices and Verify Connectivity

Part 3: Display Device Information

Background / Scenario

This is a comprehensive lab to review previously covered IOS commands. In this lab, you will cable the equipment as shown in the topology diagram. You will then configure the devices to match the addressing table. After the configurations have been saved, you will verify your configurations by testing for network connectivity.

After the devices have been configured and network connectivity has been verified, you will use IOS commands to retrieve information from the devices to answer questions about your network equipment.

This lab provides minimal assistance with the actual commands necessary to configure the router. Test your knowledge by trying to configure the devices without referring to the content or previous activities.

Note: The routers used with CCNA hands-on labs are Cisco 1941 Integrated Services Routers (ISRs) with Cisco IOS Release 15.2(4)M3 (universalk9 image). The switches used are Cisco Catalyst 2960s with Cisco IOS Release 15.0(2) (lanbasek9 image). Other routers, switches, and Cisco IOS versions can be used. Depending on the model and Cisco IOS version, the commands available and output produced might vary from what is shown in the labs. Refer to the Router Interface Summary Table at the end of this lab for the correct interface identifiers.

Note: Ensure that the routers and switches have been erased and have no startup configurations. Consult with your instructor for the procedure to initialize and reload a router and switch.

Required Resources

1 Router (Cisco 1941 with Cisco IOS Release 15.2(4)M3 universal image or comparable)

1 Switch (Cisco 2960 with Cisco IOS Release 15.0(2) lanbasek9 image or comparable)

2 PCs (Windows 7 or 8 with terminal emulation program, such as Tera Term)

Console cables to configure the Cisco IOS devices via the console ports

Ethernet cables as shown in the topology

Note: The Gigabit Ethernet interfaces on Cisco 1941 routers are autosensing and an Ethernet straight-through cable may be used between the router and PC-B. If using another model Cisco router, it may be necessary to use an Ethernet crossover cable.

Set Up Topology and Initialize Devices

Cable the network as shown in the topology.

Attach the devices shown in the topology diagram, and cable, as necessary.

Power on all the devices in the topology.

Initialize and reload the router and switch.

If configuration files were previously saved on the router and switch, initialize and reload these devices back to their basic configurations.

Configure Devices and Verify Connectivity

In Part 2, you will set up the network topology and configure basic settings, such as the interface IP addresses, device access, and passwords. Refer to the Topology and Addressing Table at the beginning of this lab for device names and address information.

Assign static IP information to the PC interfaces.

Configure the IP address, subnet mask, and default gateway settings on PC-A.

Configure the IP address, subnet mask, and default gateway settings on PC-B.

Ping PC-B from a command prompt window on PC-A.

Why were the pings not successful?

____________________________________________________________________________________

Configure the router.

Console into the router and enable privileged EXEC mode.

Enter configuration mode.

Assign a device name to the router.

Disable DNS lookup to prevent the router from attempting to translate incorrectly entered commands as though they were host names.

Assign
class as the privileged EXEC encrypted password.

Assign
cisco as the console password and enable login.

Assign
cisco as the VTY password and enable login.

Encrypt the clear text passwords.

Create a banner that warns anyone accessing the device that unauthorized access is prohibited.

Configure and activate both interfaces on the router.

Configure an interface description for each interface indicating which device is connected to it.

Save the running configuration to the startup configuration file.

Set the clock on the router.

Note: Use the question mark (
?) to help with the correct sequence of parameters needed to execute this command.

Ping PC-B from a command prompt window on PC-A.

Were the pings successful? Why?

____________________________________________________________________________________

Display Device Information

In Part 3, you will use
show commands to retrieve information from the router and switch.

Retrieve hardware and software information from the network devices.

Use the
show version command to answer the following questions about the router.

What is the name of the IOS image that the router is running?

____________________________________________________________________________________

How much DRAM memory does the router have?

____________________________________________________________________________________

How much NVRAM memory does the router have?

____________________________________________________________________________________

How much Flash memory does the router have?

____________________________________________________________________________________

Use the
show version command to answer the following questions about the switch.

What is the name of the IOS image that the switch is running?

____________________________________________________________________________________

How much dynamic random access memory (DRAM) does the switch have?

____________________________________________________________________________________

How much nonvolatile random-access memory (NVRAM) does the switch have?

____________________________________________________________________________________

What is the model number of the switch?

____________________________________________________________________________________

Display the routing table on the router.

Use the
show ip route command on the router to answer the following questions.

What code is used in the routing table to indicate a directly connected network? _____

How many route entries are coded with a C code in the routing table? _________

What interface types are associated to the C coded routes?

_______________________________________________________________________________________

Display interface information on the router.

Use the
show interface g0/1 to answer the following questions.

What is the operational status of the G0/1 interface?

_______________________________________________________________________________________

What is the Media Access Control (MAC) address of the G0/1 interface?

_______________________________________________________________________________________

How is the Internet address displayed in this command?

_______________________________________________________________________________________

Display a summary list of the interfaces on the router and switch.

There are several commands that can be used to verify an interface configuration. One of the most useful of these is the
show ip interface brief command. The command output displays a summary list of the interfaces on the device and provides immediate feedback to the status of each interface.

Enter the
show ip interface brief command on the router.

R1#
show ip interface brief

Interface IP-Address OK? Method Status Protocol

Embedded-Service-Engine0/0 unassigned YES unset administratively down down

GigabitEthernet0/0 192.168.0.1 YES manual up up

GigabitEthernet0/1 192.168.1.1 YES manual up up

Serial0/0/0 unassigned YES unset administratively down down

Serial0/0/1 unassigned YES unset administratively down down

R1#

Enter the
show ip interface brief command on the switch.

Switch#
show ip interface brief

Interface IP-Address OK? Method Status Protocol

Vlan1 unassigned YES manual up up

FastEthernet0/1 unassigned YES unset down down

FastEthernet0/2 unassigned YES unset down down

FastEthernet0/3 unassigned YES unset down down

FastEthernet0/4 unassigned YES unset down down

FastEthernet0/5 unassigned YES unset up up

FastEthernet0/6 unassigned YES unset up up

FastEthernet0/7 unassigned YES unset down down

FastEthernet0/8 unassigned YES unset down down

FastEthernet0/9 unassigned YES unset down down

FastEthernet0/10 unassigned YES unset down down

FastEthernet0/11 unassigned YES unset down down

FastEthernet0/12 unassigned YES unset down down

FastEthernet0/13 unassigned YES unset down down

FastEthernet0/14 unassigned YES unset down down

FastEthernet0/15 unassigned YES unset down down

FastEthernet0/16 unassigned YES unset down down

FastEthernet0/17 unassigned YES unset down down

FastEthernet0/18 unassigned YES unset down down

FastEthernet0/19 unassigned YES unset down down

FastEthernet0/20 unassigned YES unset down down

FastEthernet0/21 unassigned YES unset down down

FastEthernet0/22 unassigned YES unset down down

FastEthernet0/23 unassigned YES unset down down

FastEthernet0/24 unassigned YES unset down down

GigabitEthernet0/1 unassigned YES unset down down

GigabitEthernet0/2 unassigned YES unset down down

Switch#

Reflection

If the G0/1 interface showed administratively down, what interface configuration command would you use to turn the interface up?

_______________________________________________________________________________________

What would happen if you had incorrectly configured interface G0/1 on the router with an IP address of 192.168.1.2?

_______________________________________________________________________________________

Call toll free: +1 (304) 900-6229 or Request a call

Our Services

Lab – Building a Switch and Router Network Lab – Building a Switch and Router Network Topology

image1.png

image2.jpeg

Share This Post

Related Questions

Prepare the peer’s presentation topic by finding and reviewing the Internet resources and documents about the topic that you are assigned to

file attached. 1 Week 1 – Discussion: AI in Business Consider what you have read so far in the learning materials for Week 1

The Enterprise Architecture Repository is an online, web-based platform designed to store and organize Enterprise Architecture artifacts produced by EA

Instructions: Q1. Design a program that asks the user to enter a series of 20 numbers. The program should store the numbers in a list then display the

Assignment Content 1. As individuals, we influence the world around us. Research ways in which millennials are influencing

Instructions: Q1. Design a program that asks the user to enter a series of 20 numbers. The program should store the numbers in a list then display the

do a cset diagram for Staples print department, Departments and Key Tasks: Print Services Department: In the diagram identify: ● major

IT543-4: Design an implementation of cryptographic methods for an organization. Assignment Instructions: Perform the lab described in the zip

Discussion The unit readings outline several challenges of implementing and upgrading enterprise information systems. Employees were

You must find a news or journal article that is evidence that the problem or issue you wish to study is something current and of concern. Please

test1.txt // Function with Arithmetic Expression function main returns integer; begin 7 + 2 * (5 + 4); end; test2.txt // Function with a

Project 3 – Ensemble Methods and Unsupervised Learning In this project you will explore some techniques in unsupervised learning as well as ensemble

MAKE A FUNCTIONAL DATABASE APP USING THE PICTURE I POSTED BELOW AS A REFERENCES. BE ABLE TO SAVE THE DATABASE AND ALL. I NEED SOURCE CODES AND JAR FILE.

Assignment Instructions: Research and select 3 different Big Data use cases. Create a digital artifact that details the typical business objectives and

Combine both codes or make it work with 2 separate tabs. I am using Arduino Ethernet Shield W5100 with Arduino UNO trying to send a notification to

Please arrange the files with the proper titles and project numbers 1 Project 2 JOGL OpenGL Project Overview In this project you will create a

1 Homework 4 1. (10 pts) For the following program, explain the interesting elements related to threads. Focus on explaining the output of the

1 Project 2 JOGL OpenGL Project Overview In this project you will create a unique 3 graphics scene composed of OpenGL graphic components using

Use Our 6 Free Tools